Home > Error Code > Balboa Hot Tub Error Codes

Balboa Hot Tub Error Codes

Contents

In most cases overheat issues are related to the relays on the circuit board, or the temp sensor has failed and will need to be replaced. HL = High limit switch tripped. SEoP = Sensor open or disconnected. The Spa or Hot Tub Panel Displays: dr, dry This indicates that there is not enough water in the heater. Check This Out

You can follow any responses to this entry through the RSS 2.0 feed. Wird geladen... Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F.SEoP = Sensor open or disconnected. Categories Consumer Research for Best Hot Tub (99) hottubworks.com (126) life (130) spa chemicals (67) spa covers (160) Spa Crystals (11) spa filter (31) spa heater (25) Spa Ozone (17) Spa http://www.spadepot.com/spa-error-codes.htm

Balboa Hot Tub Error Codes

ICE2 = Freeze protection. Heat Related Pump Not Running.8. PSoC = Pressure switch open with circulating pump. If water temperature drops 20ºF below set temperature, low speed pump and heater activates to bring temperature within 15º of set temperature.

  1. If you have a Circ Pump, do this first (EL version):- Push the Jets 1 button once.
  2. dr = Inadequate water detected in heater.
  3. As a responsible adult, always check the topside control panel display for errors and verify safe water temperature before using a spa, and before allowing children to use a spa.
  4. Under NO circumstances should a pump be allowed to run without priming beyond the end of the 4 minute Priming Mode.

However, the usual cause for spa temp sensor error codes is that the water flow is insufficient, and when water moves too slowly through the heater, it doesn't remove the heat All Reminder Messages can be Disabled through the Topside Panel Users Menu.Note: The Balboa Default is to have this Message Disabled. OHH = Overheat. Marquis Spa Error Codes Note: Internal freeze protection only functions when there is proper power running to the spa, and the control system is operational.

Back to Top CFE or CONFIG ERROR Message There is a "Configuration Error" (CFE) in the Dip Switches or Configuration Settings.This Error Message indicates that the Dip Switch Numbers Displayed or Vita Spa Error Codes You must be logged in to post a comment. Drain and Refill the Spa Water per Manufacturers Instructions. check here Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.

Heater disabled but the spa is operational. Great Lakes Hot Tub Error Codes Blocked Suction Fitting.3. Refill, if necessary. You can also check the pressure switch or flow switch with a an Ohm meter.

Vita Spa Error Codes

The Spa or Hot Tub Panel Displays: Cd, CLd This indicates that a sensor detects a possible freeze condition. http://www.hottubworks.com/blog/spa-hot-tub-error-codes-oh-ohh-omg/ Back to Top HFL, HL, or HTR FLOW LOW Message Possibly the "Heater Flow is Low" (HFL or HL).During Heating, this message indicates a Possible Low Flow Condition. Balboa Hot Tub Error Codes There is Not Enough Water Flow through the Heater to carry the Heat Away from the Heating Element. How To Fix Flo Error Hot Tub System will restart when temp.

Monitoring the Sensors will Continue for 1 Hour. http://wiiplay.net/error-code/vpn-error-codes.html One sensor has detected 118º F. Some panels need a prompt from you to restart. The temp sensor is the larger of the two silver bullets. Hot Tub Error Code Oh

FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end. See M7 Sensors here. Browse by Price $0 - $24.99 $25 - $49.99 Over $50 CUSTOMER SERVICE Contact Us Shipping Return Policy Privacy Policy Testimonials MY ACCOUNT View Cart Account Anmelden Statistik 11.734 Aufrufe 15 Dieses Video gefällt dir? this contact form If it's not flowing after two minutes, turn the power off and let the spa rest for a few hours, then repeat.

PSoL = Pressure switch open with low pump. Coleman Spa Error Codes Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. If the water is still hotter than the set temperature, press the blower button (if applicable) to cool the spa.If your spa is not overheating based on physical vessel temperature and

Status of the heater element is unknown.

No action is necessary.I CE2 = Freeze protection. Wird geladen... Über YouTube Presse Urheberrecht YouTuber Werbung Entwickler +YouTube Nutzungsbedingungen Datenschutz Richtlinien und Sicherheit Feedback senden Probier mal was Neues aus! Underneath the spa, check that all valves are open (handles up). Coast Spa Error Codes The Heater and Pump will Operate Any time the Thermostat Demands Heat.

If the GFCI does not trip for some reason, the gFI fault will appear and the HOt flag will be set.If the spa is subsequently powered down and then powered up So, the next time your spa throws you a OH, OHH or some other Overheat error code, you know what to do. One sensor has detected 118º F at heater. http://wiiplay.net/error-code/msi-error-codes.html Wait 4 Minutes or Press any Temp Related Button to Exit Priming Mode to Normal Operation.Note: On some Early VS and GS Systems (prior to Version 23) equipped with a "Mode"

If alternating with temp, may be temporary condition. Snb = Spa is shut down. In some instances it may be more prudent to contact a local repairman or send Spa Care Center your control box for evaluation/repair. Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit sensor malfunction Sn3 =

Back to Top Your cart is empty. Wähle deine Sprache aus. What causes a Spa to Overheat? Too Many Closed Jets.6.

Veröffentlicht am 11.11.2014Check out this helpful how-to video on troubleshooting and correcting an SN3 error code on a Leisure Bay hot tub. If display shows only this message (blinking) spa is shut down. All Automatic Functions Remain OFF during this time.